8/6/2023 0 Comments Linux monit config![]() This may be tested with monit -t: # monit -tĬannot translate 'jaktest1' to FQDN name - Name or service not known Use address 0.0.0.0 # only accept connection from localhostĠ.0.0.0/0.0.0.0 # allow localhost to connect to the server and # sed -i 's/use address localhost/use address 0.0.0.0/' monitrc Use the 172.16.1.130 above or the address 0.0.0.0 if there are multiple home addresses (for instance ethernet and ppp). This could be a fixed address used by the device: # ip addr show eth0Ģ: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 Use address localhost # only accept connection from localhostĪllow 0.0.0.0/0.0.0.0 # allow localhost to connect to the server and Now listen on all local addresses (or it could be the address range of the PC’s running a web browser): # sed -i 's?allow localhost?allow 0.0.0.0/0.0.0.0?' monitrc # sed -i 's/admin:monit/admin:mtech2205/' monitrcĪllow admin:mtech2205 # require user 'admin' with password 'monit' ![]() In file /etc/monitrc, you configure a userid and password for monit: # cd /etc Using localhost is not helpful without some kind of IP forwarding (not covered here). Operating a web browser on Conduit ® is not supported. This may be helpful in testing and setting up monit. You do not need to set up the addresses for monit, if you do not wish to monitor anything manually. Otherwise download monit, and install it on your system: # opkg install monit_5.12.2-r1.0_arm926ejste.ipk General configuration of monit Set up monit to start on boot: # sed -i 's/="no"/="yes"/' /etc/default/monit Package monit (5.12.2-r1.0) installed in root is up to date. If you have an internet connection: # opkg install monit Monit reconnects PPP and restarts lora-packet-forwarder for you automatically. Most release job only start a single process.NOTE: With regards to ppp connections and lora-packet-forwarder, carriers can log off PPP at any time. This is how you can tell which processes belong to which release job. var/vcap/jobs/redis-server/monit) with final monit configuration for that release job. Each release job directory contains a monit file (e.g. Before you can run the command you have to switch to become a root user (via sudo su) since Monit executable is only available to root users.Įach enabled release job has its own directory in /var/vcap/jobs/ directory. On any BOSH managed VM, you can access Monit status for release jobs' processes via Monit CLI. To determine what the problem is with a specific VM, you can ssh into the VM and look at the logs and/or Monit directly. Unresponsive: the Director did not receive any response from the Agent ![]() Starting state indicates that one or more of the release jobs' processes are being started and may not yet be running. Starting: the Director received a response from the Agent and the Agent reported its aggregate status as starting. Failing state indicatates one or more of the release jobs' processes is not successfully running (could be failing to start, or exiting after some time, or still in the process of becoming healthy, etc.). Running state indicates that all release jobs' processes are successfully running at that moment.įailing: the Director received a response from the Agent and the Agent reported its aggregate status as not successful. Running: the Director received a response from the Agent and the Agent reported its aggregate status as successful. There are several typical values for State: | Instance | State | Resource Pool | IPs | Recovery from a vSphere Network Partitioning Fault Director SSL Certificate Configuration with OpenSSL ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |